ME221 Standalone Fuel Injection ECU, Ford Zetec Plug and Play Pack


The ME221 Wire-In ECU is a feature rich and future proof four cylinder injection engine management system. Built from the ground up using the latest control strategies means a modern, powerful, VE based ECU, with enhanced feature set including closed loop boost, in-built Wideband Lambda Control, DSP Knock Control, on-board data Logging and VVT control – all in a compact form factor. Massive IO means the ME221 can handle anything thrown at it, and custom tables means any specific algorithms required can be easily derived.

The ECU comes complete with a fully terminated Ford Zetec 1.8/2.0 Blacktop loom to get you up and running in no time. It is suitable for either the stock inlet, or throttle bodies.

Tuning Software (MEITE)

  • Intuitive, developed with real-world feedback from 100’s of tuners
  • Everything real-time adjustable
  • Diagnostics and analysis functionality
  • Custom layouts, tabs and functions
  • In-built firmware update tool for ease-of-use
  • Custom “part calibration” import – use settings from other maps in a current map
  • Offline Editing of calibrations
  • Real-time tracing
  • Data-logging of all variables and Auto-Tune

Fuelling Control

  • Configurable Load/RPM BINS 16×16, 32 bit floating point Tables
  • Multiple Fuel Tables
  • Injection Angle
  • Priming Pulse Settings and Crank Pulse Settings
  • Cranking Enrichment
  • After-Start Enrichment and ASE Time Decay
  • Warm-Up Enrichment
  • Acceleration Enrichement TPS/MAP based with Coolant Modifier
  • IAT Correction Table
  • Idle Trims
  • 16×16 AFR Target Table factored into VE Equation
  • Speed-Density/Alpha-N with optional Blending
  • Injector Voltage Offset Table
  • Overrun Fuel Cut
  • Closed Loop Narrow-band/Wide-band Lambda control with Bosch LSU4.9 Controller On-Board
  • Flex-Fuel secondary tables

Ignition Control

  • 16×16 32bit Table
  • Closed Loop DSP Windowed Knock Control On-board
  • Battery Voltage Dwell Correction 16×16 Table
  • Individual Cylinder Trimming
  • IAT and Coolant Trim
  • Spark-Scatter Ignition Idle Control
  • Flex-Fuel Control
  • Switchable Ignition Tables

Crank/Cam Triggering

  • VR/Hall/Opto Inputs as required
  • Auto-scaling, Parametric Noise Rejection
  • Range of OEM Patterns Supported

Idle Control

  • PWM based Closed/Open/Manual Diagnostic Modes
  • 4-wire Stepper based idle control
  • Cranking/Return to idle Settings reference Open-Loop table for wide-control
  • DBW Idle Control *where DBW is used
  • AC/Fan Auto-Idle Up Settings
  • PID Based for Accuracy
  • Fuel Modifiers
  • Ignition Spark Scatter
  • Jacked-Throttle Miss-Bang Idle Mode (Group-N ALS)

Knock Control

  • DSP Angular Windowed Knock Control
  • Settable Gains, Offset and Window Duration
  • Step Retard and Fail-Safe

Boost Control

  • Closed/Open Loop Boost Control by 16×16 RPM and Throttle table
  • Boost-by-Gear
  • Switchable Boost Tables
  • Over-Boost Protection
  • Pre-Start Duties
  • Anti-Lag Group-N

Variable Valve Timing

  • Fully Closed Loop PWM (Throttle X RPM table)
  • Dual Cam Support
  • Locked Angle or Locked Duty testing modes
  • Basic On/Off Mode (Honda V-Tec)
  • Supported patterns include MX5 2001-2005 and Ford ST170, Ford Puma 1.7
  • PID Tuning with Oil Temperature triggering & safeties
  • Programmable Rest State & Offset compensation

General Purpose Tables

  • 6x General Purpose Tables
  • Custom Variables and Outputs
  • Modify Fuel, Ignition, Boost and Idle strategies from the GPTs
  • 3D and 2D tables with ability to “chain” tables together for create complex functions

Communications

  • Industry Preferred RS232 for ECU mapping/communication (USB Adaptor available)
  • CAN-Bus on some models
  • USB on some models

Processing Power

  • 120Mhz 32-bit RISC Processor
  • Ignition Accuracy to 0.01 degrees, Fuelling to 0.001mS
  • 32-bit maths and tables (Table entries can have 8 decimal places for very high resolution)
  • ADCs/Analogue data reported to 16-bit accuracy
  • 20,000+ RPM

Analogue/Digital Inputs

  • Configurable “HRT”‘s for every analogue channel – use any sensor. Basemaps pre-set for factory sensors.
  • Wide-band O2 LSU4.9 Controller Built In
  • TPS, IAT, CLT, MAP, Lambda standard inputs
  • Selectable feature for digital/analogue inputs
  • Spare/unused analogue lines can be used for general purpose tables or digital switches

Environmental & Physical

  • Automotive -20 – 85*C
  • Voltage 5.5-28V
  • Operating Current Approx 120mA @ 13v
  • Electrically isolated and protected inputs/outputs
  • 90 Way Automotive Connector
  • IP67 Sealed Alloy Casing

DataLogging

  • 4Gb On-board Data logging – over 2,000 Hours of all variables
  • Unlimited PC based logging via MEITE
  • User settable Triggers and markers

 


The connections provided in our FORD ZETEC loom are:


4x 2 PinMini-Timer for the Injectors

1x 2 Pin Mini-Timer for Cam Sensor

1x 2 Pin Mini-Timer VR Type Crank Sensor

1x 2 Pin Mini-Timer for Idle Control Valve ○ Depending on stock location as it can differ by year you may need to extend this.

1x 2 Pin Mini-Timer for IAT and Coolant sensor ○ Note may need extending/changing depending on the engine type. Use OEM connectors. ● 1x Ford Coil Pack Connector

1x 3 Pin Mini-Timer for throttle sensor ○ Typical if using throttle bodies - may need to change if keeping OEM throttle sensor though this is rare.

1x 3 Pin Mini-Timer MAP sensor (suits our 3 Bar Sensor)

1 x Bosch O2/Lambda Plug.

Auxiliary flying wires for spare outputs, tachometer, knock and O2/Lambda.


Loom details can be found in this document.

 

What is in the box:


1 x Standalone ME221 Engine Control Unit (ECU)

1 x Zetec Loom (supplied as standard with 2 pin mini timer injector connectors to suit standard Zetec, please see our other listings for motorcycle injector connectors) 


Options


Coolant and air temperature sensors. The ME221 and MEITE software do offer the ability to calibrate the ECU to read any sensor, however by using the sensors on offer in this listing the standard calibration tables can be used - vastly simplifying the set-up process and saving considerable time. Both sensors are M12 x 1.5 thread. The additional coolant temperature sensor housing offers a quick and convenient method for installing directly into a radiator top hose and negates the need for tapping out existing holes in your cylinder head.

Crank Sensor. The ME221 ECU will work with the standard Zetec crank sensor. This sensor is therefore offered as a direct replacement and only required if you are unsure of your existing sensors condition or reliability. 

Data Cable (FTDI USB-Serial Adaptor). Whilst the ECU comes with an RS232 cable many modern Laptops do not have such a connection. Therefore this adaptor will allow a USB port to be used for connectivity. This genuine FTDI cable is guaranteed to work with this ECU, unlike many cheaper alternatives that often suffer connectivity issues.


Basemaps


ALL ME221 and ME442 ECU's are shipped with a test map only. This is highly unlikely to run your engine and if it does it will not run it very well! A library of basemaps can be found here on the Motorsport Electronics Support Pages as well as a full suite of installation manuals. danST Engineering can also provide basemaps for a variety of engines developed on our in-house rolling road.


Coil Pack Compatibility


This ECU is intended for use with wasted spark Ford coil packs. Other wasted spark coil packs may be compatible however please contact us before attempting to use alternatives to avoid potential damage to the ECU. The fitment of a Ford coil pack (available in our shop) will guarantee compatibility and reliability.



Note: As with all after-market engine management systems (ECU’s) a dyno tuning is recommended to avoid damaging your engine and to get the most out of your engine. A full range of basemaps are available online from danST engineering or Motorsport Electronics. 

 

Write a review

Note: HTML is not translated!
   Bad           Good

ME221 Standalone Fuel Injection ECU, Ford Zetec Plug and Play Pack

  • £745.82

  • Ex Tax:£745.82

Available Options


Related Products

ME221 Gen2 Standalone Fuel Injection ECU & Universal Unterminated Loom

ME221 Gen2 Standalone Fuel Injection ECU & Universal Unterminated Loom

ME221 Standalone Wire-In ECU. The ME221 Wire-In ECU is a feature rich and future proof four cylin..

£620.83 Ex Tax:£620.83

Nodiz Pro Ignition ECU, Ford Zetec Plug and Play Pack (Gen X)

Nodiz Pro Ignition ECU, Ford Zetec Plug and Play Pack (Gen X)

PRELOOMED/PREMAPPED NODIZ ZETEC SYSTEM If you have the factory Coil Pack and Crank Sensor on your..

£275.00 Ex Tax:£275.00

ME221 Standalone Fuel Injection ECU, Ford ST170 Plug and Play Pack

ME221 Standalone Fuel Injection ECU, Ford ST170 Plug and Play Pack

ME221 Standalone Fuel Injection ECU, Ford ST170 Plug and Play Pack The ME221 ST170 loom is comple..

£745.82 Ex Tax:£745.82

ME221 Gen2 Standalone Fuel Injection ECU For Vauxhall Engines

ME221 Gen2 Standalone Fuel Injection ECU For Vauxhall Engines

ME221 Gen2 Standalone Fuel Injection ECU For Vauxhall enginesThe ME221 Wire-In ECU is a feature rich..

£745.82 Ex Tax:£745.82

Ford/Mazda Duratec 2.5 - 50mm DCOE ULTIMATE ROAD Individual Throttle Body Kit

Ford/Mazda Duratec 2.5 - 50mm DCOE ULTIMATE ROAD Individual Throttle Body Kit

This individual throttle body kit for fitment to the Ford & Mazda 2.5 Duratec Engine. 50mm DCOE..

£2,600.00 Ex Tax:£2,600.00

Suzuki Ignis M15A DCOE Individual Throttle body kit

Suzuki Ignis M15A DCOE Individual Throttle body kit

A complete indivudual throttle body kit for the the Suzuki Jimny and Ignis 1.3 M13A a..

£958.33 Ex Tax:£958.33

Toyota 3SGE Rev 2 Individual Throttle bodies kit, All Diameters

Toyota 3SGE Rev 2 Individual Throttle bodies kit, All Diameters

A complete indivudual throttle body kit for the the Toyota 3SGE3, featuring DCOE type thro..

£897.16 Ex Tax:£897.16

Lotus Twin Cam DCOE Individual Throttle bodies kit, 40mm

Lotus Twin Cam DCOE Individual Throttle bodies kit, 40mm

A complete 40mm DCOE individual throttle body kit for the Lotus Twin Cam engine that originally..

£2,500.00 Ex Tax:£2,500.00

Porsche 964 3.6 45-50mm SF Individual Throttle body kit with ECU package

Porsche 964 3.6 45-50mm SF Individual Throttle body kit with ECU package

A complete individual throttle body kit for the the Porsche 964 3.6, featuring SF typ..

£4,500.00 Ex Tax:£4,500.00

ME221 Gen2 Standalone Fuel Injection ECU ONLY

ME221 Gen2 Standalone Fuel Injection ECU ONLY

ME221 Standalone ECU ONLY. ME221 Gen2 Standalone Fuel Injection ECU For Vauxhall enginesThe ME221..

£537.50 Ex Tax:£537.50

Ford Zetec 1.8/2.0 DCOE Individual Throttle bodies kit, All Diameters

Ford Zetec 1.8/2.0 DCOE Individual Throttle bodies kit, All Diameters

A complete indivudual throttle body kit for the the Ford Zetec engine (1.6/1.8/2.0 Blackto..

£950.00 Ex Tax:£950.00

Ford/Mazda Duratec 2.5 - 50mm DCOE FAST ROAD PACK Individual Throttle Body Kit

Ford/Mazda Duratec 2.5 - 50mm DCOE FAST ROAD PACK Individual Throttle Body Kit

This individual throttle body kit for fitment to the Ford & Mazda 2.5 Duratec Engine. 50mm DCOE..

£2,000.00 Ex Tax:£2,000.00

Ford Pinto 1600-2300 DCOE Individual Throttle bodies kit, All Diameters

Ford Pinto 1600-2300 DCOE Individual Throttle bodies kit, All Diameters

A complete indivudual throttle body kit for the the Ford Pinto Engine, featuring DCOE..

£950.00 Ex Tax:£950.00

Tags: ME221, ECU, MOTORSPORT ELECTRONICS