PRELOOMED/PREMAPPED NODIZ Vauxhall SYSTEM

If you have the factory Coil Pack and Crank Sensor on your Vauxhall Engine, and are using carbs for fueling, then this package is EVERYTHING you need to have it up and running in MINUTES!

 

The innovative Nodiz Pro Ignition Management ECU. Ideal for use alongside our bike carb kits or the more traditional carburettor set-ups.

The NODIZ Pro™ is a state of the art microprocessor controlled digital stand-alone, fully mappable ignition controller for 4 or 8 cylinder spark ignition engines. It can be used either to replace older distributor based ignition systems for more modern coil packs, or even to allow the running of carburettors on more modern engines which do not feature a distributor drive.

Package Contents:

The main NODIZ Pro unit & Vauxhall loom.

ECU Features include:


  • 16 Load by 16 Speed Sites, with full 3D interpolation and user definable Speeds/Loads.
  • User settable RPM Soft and Hard Cut Rev Limiters.
  • In-built coil drivers, no need for EDIS or other modules.
  • Coolant based ignition adjustment map (To add advance to cold engines, etc.).
  • Intake Air Temperature ignition adjustment map, to allow timing retarding based on intake temperature to reduce pinking on very high intake temperatures.
  • Cranking based advance angle to help start high compression engines.
  • A programmable Shift Light output.
  • 5v Tachometer Output.
  • Launch Control
  • A programmable output based on either RPM (i.e. V-TEC control), coolant temperature (i.e. Fan Control) or Intake temperature (i.e. Water Injection control).
  • RS232 Connectivity Port for cable connection

  PLEASE NOTE THAT THIS IS ONLY SUITABLE FOR FORD AND VAUXHALL COIL PACKS for any others please contact us.


NOTE! The unit will require configuring to the Vauxhall settings prior to startup. This will involve connecting with a laptop/PC and changing the trigger pattern from 36-1 (Ford) to 60-2 (Vauxhall) and adjusting the trigger offset from 90degs (Ford) to 68degs (Vauxhall). It is also advised that once up and running a traditional timing light is used to double check you are seeing the correct timing at idle - fine tuning of the trigger offset can be done if any variation is found. Details of these procedures are outlined in the manual (available online).

More information can be found on the Nodiz website.

Full support and documentation is available from both danST Engineering and Motorsport Electronics. All relevant manuals, software and basemaps can be found at the below link:

https://motorsport-electronics.co.uk/software-manuals/

Write a review

Note: HTML is not translated!
   Bad           Good

Nodiz Pro Ignition ECU, Vauxhall Plug and Play Pack (Gen 2)

  • £249.17

  • Ex Tax:£249.17

Related Products

Ford CVH 37mm Bike Carburettor Starter Kit

Ford CVH 37mm Bike Carburettor Starter Kit

danST Engineering are pleased to be able to offer this complete bolt on kit for the Ford CVH en..

£500.00 Ex Tax:£500.00

Universal Trigger Wheel 140mm,  Crank Position, for Megajolt, Nodiz, Omex, ME221

Universal Trigger Wheel 140mm, Crank Position, for Megajolt, Nodiz, Omex, ME221

3mm thick CNC laser cut mild steel trigger wheel for use with any engine management system that requ..

£16.67 Ex Tax:£16.67

VW 1.8 KR, 9A, PL & 2.0 ABF, AAL, 9A Bike Carb Conversion Kit 37mm starter kit

VW 1.8 KR, 9A, PL & 2.0 ABF, AAL, 9A Bike Carb Conversion Kit 37mm starter kit

DanST Engineering are pleased to be able to offer this complete bolt on kit for the Volkswagen 1.8 '..

£500.00 Ex Tax:£500.00

A-Series Bike Carb Conversion Starter Pack

A-Series Bike Carb Conversion Starter Pack

danST Engineering are pleased to be able to offer this complete bolt on kit for the BMC/Austin A ser..

£541.67 Ex Tax:£541.67

Air Temperature Sensor for use with the ME221

Air Temperature Sensor for use with the ME221

An aftermarket air temperature sensor for use with the ME221 ECU. May also be suitable for..

£19.99 Ex Tax:£19.99

A-Series Bike Carb Manifold to Suit ZZR600 Carbs

A-Series Bike Carb Manifold to Suit ZZR600 Carbs

An Inlet Manifold for fitment to the BMC/Austin A Series Engine (998cc/1000cc/1275cc). TIG weld..

£125.00 Ex Tax:£125.00

VW 1.8 EX, DX and PB Golf Bike Carb Conversion Kit 37mm starter kit

VW 1.8 EX, DX and PB Golf Bike Carb Conversion Kit 37mm starter kit

DanST Engineering are pleased to be able to offer this complete bolt on kit for the Mk1 Volkswagen G..

£520.83 Ex Tax:£520.83

 VW Polo 1.4 8v ABU, APQ, AEX & AEE Bike Carb Conversion Kit 37mm starter kit

VW Polo 1.4 8v ABU, APQ, AEX & AEE Bike Carb Conversion Kit 37mm starter kit

DanST Engineering are pleased to be able to offer this complete bolt on kit for the Volkswagen 1.4 8..

£500.00 Ex Tax:£500.00

VW Polo 1.4 16v & Lupo Sport AFH Bike Carb Conversion Kit 37mm starter kit

VW Polo 1.4 16v & Lupo Sport AFH Bike Carb Conversion Kit 37mm starter kit

DanST Engineering are pleased to be able to offer this complete bolt on kit for the Volkswagen Polo ..

£500.00 Ex Tax:£500.00

Crank Position Sensor (VR) ford Zetec fitment, 2 Pin

Crank Position Sensor (VR) ford Zetec fitment, 2 Pin

A crank position sensor for use with ford zetec engine. This sensor can be used as a universal senso..

£24.16 Ex Tax:£24.16

Coolant Temperature Sensor and housing for use with NODIZ & ME221, *SILVER*

Coolant Temperature Sensor and housing for use with NODIZ & ME221, *SILVER*

An aftermarket Bosch style coolant temperature sensor complete with anodised silver 3..

£33.33 Ex Tax:£33.33

Coil Pack for Ford Focus & Mondeo Zetec E, wasted spark 4 cylinder

Coil Pack for Ford Focus & Mondeo Zetec E, wasted spark 4 cylinder

Suitable for wasted spark ignition for 4 cylinder engines. As originally fitted to the 1.6-2.0 Zetec..

£33.33 Ex Tax:£33.33

Wasted Spark Supplement Pack for 4 cylinder distributor based engines

Wasted Spark Supplement Pack for 4 cylinder distributor based engines

Our 'Wasted Spark Supplement Pack' is a kit of parts to facilitate the updating of older distributor..

£74.16 Ex Tax:£74.16

NODIZ Pin for main loom plug, crimp type

NODIZ Pin for main loom plug, crimp type

Spare crimp-type pin for the main plug on the NODIZ loom. Ideal for anyone wanting to add auxiliary ..

£0.20 Ex Tax:£0.20

Ignition leads (early ford coilpack type) To suit XR2I

Ignition leads (early ford coilpack type) To suit XR2I

Suitable for wasted spark ignition for 4 cylinder engines. As originally fitted to the Ford Fiesta X..

£25.00 Ex Tax:£25.00

Universal Trigger Wheel 170mm,  Crank Position, for Megajolt, Nodiz, Omex, ME221

Universal Trigger Wheel 170mm, Crank Position, for Megajolt, Nodiz, Omex, ME221

3mm thick CNC laser cut mild steel trigger wheel for use with any engine management system that requ..

£16.67 Ex Tax:£16.67

Triumph TR6 Bike Carb Conversion Kit 37mm starter kit

Triumph TR6 Bike Carb Conversion Kit 37mm starter kit

DanST Engineering are pleased to be able to offer this complete bolt on kit for the Triumph TR6 2.5l..

£833.33 Ex Tax:£833.33

Universal Trigger Wheel 190mm,  Crank Position, for Megajolt, Nodiz, Omex, ME221

Universal Trigger Wheel 190mm, Crank Position, for Megajolt, Nodiz, Omex, ME221

3mm thick CNC laser cut mild steel trigger wheel for use with any engine management system that requ..

£29.16 Ex Tax:£29.16

Map Sensor, 3 Bar Cosworth Type

Map Sensor, 3 Bar Cosworth Type

This is a Cosworth style 3-Bar MAP sensor, used for measuring manifold pressure. Capable of reading ..

£29.17 Ex Tax:£29.17

Tags: Nodiz