danST Engineering are pleased to be able to offer this complete bolt on kit for the Porsche 924 2.0 EA831 engine.

 

This package consists of the following:

 

1 x TIG welded danST Engineering Aluminium inlet Manifold

1 x Set of GSXR750 or GSXR1000 Throttle Bodies, respaced with extended linkages and fuel rail (retaining original 240cc injectors, suitable for power outputs in excess of 240bhp!)

1 x danST Engineering Fitting Kit (4x Fluoro lined silicone hoses and 8x stainless mikalor clamps) in red, blue or black

1 x 50mm Diameter, danST Aluminium Trumpet Kit complete with custom danST clamp ring assemblies                   (trumpets available in 25/50/90mm lengths, please use drop down to select)

1 x Pipercross PX500 or PX600 filter kit (C502D, C503D, C504D, C602D, C603D or C604D  depending on space and trumpet requirements)

1 x danST Engineering Throttle Linkage Kit

1 x Motorsport Electronics ME221 ECU and Ford based Loom Kit (Basemaps to get the car running are available, road mapping/tuning will be required)

1 x Air Intake Temperature Sensor

1 x Coolant Sensor and Radiator Top Hose Mounting Kit


Note that in order to run the ME221 ECU a crank position sensor arrangement will be required as well as a wasted spark coilpack. For this purpose we offer our wasted spark supplement pack as below:

Wasted Spark Supplement Pack


This kit is ideal for anyone wanting to carry out the popular bike throttle body modification. Bike throttle bodies offer excellent performance, reliability and fuel economy without the pricetag normally associated with TB conversions! Our throttle body kits are proving very popular within the Porsche 924 community as a simple system to replace the troublesome 30+ year old standard engine management. 


These conversions are very popular in both modified and kit car circles as well as Hillclimb and Motorsport applications and provide a low cost, simple power upgrade not to mention a fantastic soundtrack! During back to back dyno tests (rolling road) Bike throttle bodies have repeatedly shown peak power figures matching, or indeed exceeding those seen from other manufacturers individual throttle body kits on the same spec engine. Further to this the tapered design of these ITB's quite often gives greater torque and mid-range than those competitors. All this for a fraction of the cost of the available alternatives. These kits benefit from the massive investment that the manufacturers (Keihin and Mikuni) put into developing induction that allows a 1000cc bike to put out 170bhp+ per litre!

 

The manifold is manufactured from high quality aluminium with a precision Water Jet cut 10mm thick flange and TIG welded 48mm (Outside Dia) runners with a 3mm thick wall. All internal joints are fully ported/ground to ensure a smooth flow.

All danST supplied Throttle Bodies undergo a comprehensive inspection, strip, ultrasonic clean and rebuild process. We can also build this kit using alternative throttle bodies (38mm GSXR600, 46mm GSXR1300 or ZX12R etc) depending on customer requirements and engine specification.

 

The ME221 ECU is the latest engine management system from Motorsport Electronics LTD. Designed for fully sequential control of four cylinder engines, it is a feature packed ECU in a compact, reliable and affordable form. With Support for a range of OEM sensors and trigger patterns the ME221 has a range of features including:

 

Fully sequential fuel control

Flex-fuel

Closed Loop boost and VVT control

Windowed DSP Knock Control

Programmable inputs

custom tunable sensor tables

Full 3D mapping of both fuel and ignition

 

Kits can be customised to your requirements (eg delete the filter should you wish to utilise another solution). Buy these now and have your cars performance increased ready for the summer season! 

Please Note: All of our throttle body kits are made to order and therefore on a 10 working day lead time. This is to allow the manufacture of the manifold and preparation of the throttle bodies.

For alternative engine fitments (See other listings for the range of inlet flanges these can be mounted to) or any questions please feel free to message us. We can also be found on facebook under danST engineering.

 

This kit really is THE most affordable way to get up and running on individual EFI throttle bodies without compromising on quality and performance. 

 

 

FAQ’s:

 

 

What Else Will I need?

 

2.0 Fuel Supply

All danST Motorcycle Throttle Body kits come with the bike injectors and fuel rail included and require a typical EFI fuel supply pressure of 3 Bar (45psi). How this is achieved will depend on the vehicle:

 

2.2) OE Fuel Injected Engine. The standard fuel pump on a vehicle running EFI as standard will usually be sufficient to fuel an individual throttle body set-up (engine spec dependent).

Where an engines standard injectors and fuel rail are mounted in the inlet manifold (for example the Ford Zetec) it is necessary to utilise the bike injectors and rail. The removal of the original fuel rail and injectors will also likely delete the standard fuel pressure regulator and thus a replacement regulator will be required. We offer an adjustable fuel pressure regulator for this purpose (please see our shop).

Where an engines injectors mounted in the cylinder head (eg Ford Duratec & 1800 MX5) customers have the option to retain this along with the standard regulator, further simplifying the install. If this route is to be taken please advise and we can blank the bike injector holes during production of the throttle body kit.

 

Rolling Road Tune. Our throttle bodies are fully balanced prior to dispatch. However the ECU will need a mapping session using the necessary AFR equipment and under real world load conditions (usually on a rolling road). This will ensure the maximum performance is achieved and will avoid engine damage that can be associated with running excessively lean or rich.

 

What power increase will I see?

Power gains are highly dependent on other work carried out to the engine. As with any induction modifications the throttle body kits will better compliment an engine that has had an exhaust manifold and system upgrade as a minimum. Camshafts and headwork will of course further benefit the power and torque curves. We typically see 15-20bhp gains on standard 924 engines with a free flowing exhaust and well mapped.

 

 

How do I connect the fuel supply without a return on the fuel rail?

Please see the below fuel supply schematic diagram (swirl pot is optional):

 

https://drive.google.com/file/d/0B6HvwRl8vIh-YVhVeEdJWi1Icjg/view?usp=sharing

 

 

How do I connect the Throttle Position Sensor?

 

The below wiring guide covers the throttle position sensors and their colour coding for both our bike carburettor and bike throttle body kits:

 

How do I wire the ECU?

 

All support documentation for the Motorsport Electronics ECU’s can be downloaded from:

 

 

Please see our shop for accessories that will aid with the above as well as further parts to further compliment your install. Additionally you may wish to consider our range of ‘Fast Road’ and 'Competition' kits as these contain many of the accessories listed above – these kits can also be tailored to your requirements. Further advice and technical information is available on the danST Engineering homepage.

 

Write a review

Note: HTML is not translated!
    Bad           Good

Porsche 924 2.0 EA831 Individual Throttle Bodies Kit 42mm *FAST ROAD PACK*

  • £1,333.33

  • Ex Tax: £1,333.33

Available Options


Related Products

Porsche 924 2.0 EA831 Individual Throttle Bodies Kit 42mm *STARTER PACK*

Porsche 924 2.0 EA831 Individual Throttle Bodies Kit 42mm *STARTER PACK*

danST Engineering are pleased to be able to offer this bolt on kit for the Porsche 924 2.0 EA831&nbs..

£716.66 Ex Tax: £716.66

Porsche 924 EA831 2.0 37mm Bike Carburettor Deluxe Kit

Porsche 924 EA831 2.0 37mm Bike Carburettor Deluxe Kit

danST Engineering are pleased to be able to offer this complete bolt on kit for the Porsche 924 EA83..

£775.00 Ex Tax: £775.00

Porsche 924 EA831 2.0 40mm Bike Carburettor Deluxe Kit

Porsche 924 EA831 2.0 40mm Bike Carburettor Deluxe Kit

danST Engineering are pleased to be able to offer this complete bolt on kit for the Porsche 924 EA83..

£858.00 Ex Tax: £858.00

Porsche 944 / 968 S2 3.0 16V Inlet Manifold to suit DCOE/Jenvey Style Throttle Bodies

Porsche 944 / 968 S2 3.0 16V Inlet Manifold to suit DCOE/Jenvey Style Throttle Bodies

An inlet manifold to suit the Porsche 944 S2 and 968 3.0 16V engines. TIG welded in aluminium and fu..

£270.00 Ex Tax: £270.00

Porsche 944 & 924S 2.5 8V Inlet Manifold to suit DCOE/Jenvey Style Throttle Bodies

Porsche 944 & 924S 2.5 8V Inlet Manifold to suit DCOE/Jenvey Style Throttle Bodies

An inlet manifold to suit the Porsche 944 & 924S 2.5 8V engines. TIG welded in aluminium and ful..

£270.00 Ex Tax: £270.00

Tags: Porsche, 924, 2.0, EA831, water cooled, 2.5, carrera, turbo, GT, ITB,