danST Engineering are pleased to be able to offer this complete bolt on kit for the mk2.5 Mazda MX5 1800 engine with the ME221 VVT ECU. The package consists of the following:

1x TIG welded danST Engineering Aluminium inlet Manifold

1x Set of GSXR750, GSXR1000, ZX10R 42-43mm Throttle Bodies, respaced with extended linkages injectors blanked so original 265cc injectors in head (capable of 185hp) and OEM fuel rail can be retained for simplicity

1x Heavy Duty danST inlet gasket

1x danST Engineering Fitting Kit (4x Fluoro lined silicone hoses and 8x stainless mikalor clamps) in red, blue or black

50mm Diameter, danST Aluminium Trumpet Kit complete with custom danST clamp ring assemblies  (trumpets available in 25/50/90mm lengths, please use drop down to select)

***1 x Pipercross PX500 or PX600 filter kit (C502D, C503D, C504D, C602D, C603D or C604D  depending on space and trumpet requirements)

***ME221 VVT Plug N Play ECU which replaces the standard mazda ECU and offers FULL VVT control!

1 x Air Intake Temperature Sensor (required to replace removed MAF equipment)

 

***Note: In a standard MX5 engine bay we would specify 50mm long trumpets and the C504D filter as this combination will fit without modification to the vehicles inner wing/brake cylinder and pipework. Of course if the engine being used is installed in a different vehicle (eg Kit cars) then space may allow the larger C604D and 90mm trumpets.

 We now offer the upgrade to the ME442 ECU with built in wide band controller and sensor as well as SD card data logging.

This kit is ideal for anyone wanting to carry out the popular bike throttle body modification. Bike throttle bodies offer excellent performance, reliability and fuel economy without the pricetag normally associated with TB conversions! These conversions are very popular in both modified and kit car circles as well as Hillclimb and Motorsport applications and provide a low cost, simple power upgrade not to mention a fantastic soundtrack! This kit sets itself apart from others by offering full control of the variable valve timing found on the mk2.5 MX5 engine - allowing the user/tuner to maximise the potential of this popular engine.



 

The manifold is manufactured from high quality aluminium with a precision Water Jet cut 10mm thick flange and TIG welded 48mm (Outside Dia) runners with a 3mm thick wall. All internal joints are fully ported/ground to ensure a smooth flow.

All danST supplied Throttle Bodies undergo a comprehensive inspection, strip, ultrasonic clean and rebuild process.

 

 Here is a for a dyno graph of the 1800 MX5 on our throttle bodies, graph courtesy of Dyno Tech https://drive.google.com/file/d/0B6HvwRl8vIh-cWFpOFZ5a09mczQ/view?usp=sharing

Please Note: All of our throttle body kits are made to order and therefore on a 10 working day lead time. This is to allow the manufacture of the manifold and preparation of the throttle bodies.

FAQ’s:

 

 

What Else Will I need?

 

1.0 Engine Management Sensors.

Our ECU offerings require a set of basic inputs in order to function. Below is a summary of the basic inputs and outputs and the equipment you will need:

          1.1 Crank Position Sensor. All ECU's need to know where the engine       is relative to TDC at any point in time. This is achieved with a crank    position sensor reading a toothed profile (For example: Ford 36-1, or      Vauxhall 60-2) either on the engines flywheel or front pulley. If an           engine is already equipped with a crank sensor then given that the   new ECU supports the tooth pattern of the OE sensor arrangement          aftermarket sensor and trigger wheel will need to be fitted to the engines front pulley (see our shop for univeral items).

          1.2 Engine Load Sensing. This input can be achieved by either a    throttle position sensor (TPS) or Manifold Pressure Sensor (MAP). TPS      is usually the favoured method in normally aspirated applications,          however in forced induction MAP is essential. All danST throttle body         kits come complete with a throttle position sensor as standard.           Additionally the throttle bodies all have connections for a map sensor          (also useful for balancing) if required.

          1.3 Air Temperature Sensor. An ECU needs to know the inlet air    temperature to ensure fueling and ignition timing are correctly       adjusted to the working conditions. If the engine already has an air temperature sensor then this can potentially be re-used, however           temperature sensors cannot be 'piggy-backed' and thus if the original         sensor is still driving another instrument/ECU a new dedicated sensor          will need to be installed (usually in the air filter backplate, or simply         close to the inlet in the engine bay). Please see our shop for suitable       air temperature sensors.

          1.4 Coolant Temperature Sensor. An ECU needs to know the        engine coolant temperature to ensure fueling and ignition timing are     correctly adjusted to the working conditions. If the engine already has a coolant temperature sensor then this can potentially be re-used,      however temperature sensors cannot be 'piggy-backed' and thus if the       original sensor is still driving another instrument/ECU a new dedicated          sensor will need to be installed. Please see our shop for suitable    coolant temperature sensors as well as a useful radiator top hose   mounting kit.

 

          1.5 Coilpack. The ECU's ignition drivers are used to power a coilpack         (typically 'wasted spark'). Therefore the engine will require a coilpack      and matching ignition leads - most 'modern' engines have a coilpack       fitted as standard. Older, typically carburated engines will require one fitting. Please see our shop for suitable coilpacks.

 

2.0 Fuel Supply

All danST Motorcycle Throttle Body kits come with the bike injectors and fuel rail included and require a typical EFI fuel supply pressure of 3 Bar (45psi). How this is achieved will depend on the vehicle:

 

2.1) OE Carburettor Engine. Carburated engines generally run on a low pressure fuel supply of around 3psi and therefore the fuel supply will not be sufficient from the standard (or aftermarket) fuel pump on an engine originally equipped with carburettors. Therefore a high pressure EFI fuel pump will be required along with the appropriate fuel pressure regulator. We offer high pressure EFI fuel pumps and adjustable fuel pressure regulators in our shop for this application. A schematic of the fuel supply plumbing can also be seen in the technical section of our website. It is worth noting that if you are already running an aftermarket electric pump for the carburettors this can be retained to feed a swirl pot (which in turn feeds the high pressure pump). Please see the diagram on our website for more details.

 

2.2) OE Fuel Injected Engine. The standard fuel pump on a vehicle running EFI as standard will usually be sufficient to fuel an individual throttle body set-up (engine spec dependent).

Where an engines standard injectors and fuel rail are mounted in the inlet manifold (for example the Ford Zetec) it is necessary to utilise the bike injectors and rail. The removal of the original fuel rail and injectors will also likely delete the standard fuel pressure regulator and thus a replacement regulator will be required. We offer an adjustable fuel pressure regulator for this purpose (please see our shop).

Where an engines injectors mounted in the cylinder head (eg Ford Duratec & 1800 MX5) customers have the option to retain this along with the standard regulator, further simplifying the install. If this route is to be taken please advise and we can blank the bike injector holes during production of the throttle body kit.

 

3) Throttle Linkage. The throttle cable connection is relatively simple on bike throttle bodies in comparison to other aftermarket offferings with no complicated linkages required. In most cases it is simply a case of adapting the end of the existing throttle cable (inner and outer) to interface with the carbs. Our throttle body kits come with the basic parts to achieve this adaptation, or the danST universal cable kit can be used to make a cable assembly up (see our shop for this kit).

4) Rolling Road Tune. Our throttle bodies are fully balanced prior to dispatch. However the ECU will need a mapping session using the necessary AFR equipment and under real world load conditions (usually on a rolling road). This will ensure the maximum performance is achieved and will avoid engine damage that can be associated with running excessively lean or rich.

 

 

Are the danST Throttle Body Kits Compatible with my Fly-by-wire throttle?

Any vehicle fitted with a fly-by-wire (electronic) throttle will need to be adapted to a traditional cable arrangement.

 

 

What power increase will I see?

Power gains are highly dependent on other work carried out to the engine. As with any induction modifications the throttle body kits will better compliment an engine that has had an exhaust manifold and system upgrade as a minimum. Camshafts and headwork will of course further benefit the power and torque curves. A typical healthy 2.0 Ford Zetec (standard 135bhp) will see 165-170bhp with an ITB kit and free flowing exhaust when correctly mapped. Please also see the various customer power graphs posted on our website for typical examples.

 

 

How do I connect the fuel supply without a return on the fuel rail?

Please see the below fuel supply schematic diagram (swirl pot is optional):

 

https://drive.google.com/file/d/0B6HvwRl8vIh-YVhVeEdJWi1Icjg/view?usp=sharing

 

 

How do I connect the Throttle Position Sensor?

 

The below wiring guide covers the throttle position sensors and their colour coding for both our bike carburettor and bike throttle body kits:

 

How do I wire the ECU?

 

All support documentation for the Motorsport Electronics ECU’s can be downloaded from:

Any questions please ask. For alternative engine fitments or any questions please feel free to email us.

We can also be found on: facebook,Instagram and Twitter under danST Engineering

 

 

Write a review

Note: HTML is not translated!
   Bad           Good

Mazda MX5 NB 1600 & 1800 Individual Throttle Bodies Kit 42mm, VVT 01-05 danST FAST ROAD PACK

  • Brands danST Engineering
  • Product Code:MX5180105-GSXR1000TB-KITFR
  • Availability:In Stock
  • £1,400.00

  • Ex Tax:£1,400.00

Available Options


Related Products

ME221 Gen 2 Plug-in MX5 NB2.5 VVT 01-05 (3 Plug) ECU

ME221 Gen 2 Plug-in MX5 NB2.5 VVT 01-05 (3 Plug) ECU

The ME221 MX-5 PnP is the latest plug-n-play Engine Management System from Motorsport Electronics fo..

£579.17 Ex Tax:£579.17

Mazda MX5 mk1 NA 1800 Individual Throttle Body Kit 42mm, Eunos danST STARTER PACK

Mazda MX5 mk1 NA 1800 Individual Throttle Body Kit 42mm, Eunos danST STARTER PACK

Mazda MX5 mk1 NA 1800 Individual Throttle Body Conversion Kit danST STARTER PACK   d..

£764.17 Ex Tax:£764.17

Mazda MX5 mk2 NB 1800 Individual Throttle Body Kit 42mm, Eunos danST STARTER PACK

Mazda MX5 mk2 NB 1800 Individual Throttle Body Kit 42mm, Eunos danST STARTER PACK

Mazda MX5 mk2 NB 1800 Individual Throttle Body Conversion Kit danST STARTER PACK   d..

£764.17 Ex Tax:£764.17

Mazda MX5 NA/NB 1600 Bike Throttle Bodies Kit GSXR 40mm, Eunos danST STARTER PACK

Mazda MX5 NA/NB 1600 Bike Throttle Bodies Kit GSXR 40mm, Eunos danST STARTER PACK

Mazda MX5 NA/NB 1600 Bike Throttle Body Conversion Kit danST STARTER PACK   dan..

£764.17 Ex Tax:£764.17

ME442 Plug-In MX5 NB 01-05 (3 Plug) ECU

ME442 Plug-In MX5 NB 01-05 (3 Plug) ECU

TDescriptionThe ME442 MX-5 Plug-In is our latest Engine Management System for the Mk2/NB ‘Facelift’ ..

£745.83 Ex Tax:£745.83

ME442 Plug-In MX5 NA 96-98 (3 Plug) ECU

ME442 Plug-In MX5 NA 96-98 (3 Plug) ECU

TDescriptionThe ME442 MX-5 Plug-In is our latest Engine Management System for the Mk1 (3 Plug NA) MX..

£745.83 Ex Tax:£745.83

ME442 Plug-In MX5 NB 99-00 (3 Plug) ECU

ME442 Plug-In MX5 NB 99-00 (3 Plug) ECU

TThe ME442 MX-5 Plug-In is our latest Engine Management System for the Mk2/NB (3 Plug NA) MX-5 / Mia..

£745.83 Ex Tax:£745.83

ME442 Plug-In MX5 NA 89-95 (2 Plug) ECU

ME442 Plug-In MX5 NA 89-95 (2 Plug) ECU

The ME442 MX-5 Plug-In is our latest Engine Management System for the Mk1 (2 Plug NA) MX-5 / Miata, ..

£745.83 Ex Tax:£745.83

ME360 & ST170 Loom Package

ME360 & ST170 Loom Package

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£912.50 Ex Tax:£912.50

ME360 Standalone Fuel Injection ECU, Ford Duratec Plug and Play Pack

ME360 Standalone Fuel Injection ECU, Ford Duratec Plug and Play Pack

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£912.50 Ex Tax:£912.50

ME360 & C20XE/C20LET Loom Package

ME360 & C20XE/C20LET Loom Package

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£912.50 Ex Tax:£912.50

ME360 Wire-In ECU with Universal Unterminated Loom

ME360 Wire-In ECU with Universal Unterminated Loom

The ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder injection engi..

£829.17 Ex Tax:£829.17

ME360 & Honda F20C S2000 Loom Package

ME360 & Honda F20C S2000 Loom Package

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£1,125.00 Ex Tax:£1,125.00

ME360 & Ford Zetec Loom Package

ME360 & Ford Zetec Loom Package

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£912.50 Ex Tax:£912.50

ME360 & Honda K20 Loom Package, EP3 Civic Type R, K-Swap

ME360 & Honda K20 Loom Package, EP3 Civic Type R, K-Swap

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£1,125.00 Ex Tax:£1,125.00

ME360 ECU ONLY

ME360 ECU ONLY

DescriptionThe ME360 Wire-In ECU is a feature rich and future proof four, six and eight cylinder inj..

£704.17 Ex Tax:£704.17

ME221/ME360 Gen2 3m Unterminated Loom

ME221/ME360 Gen2 3m Unterminated Loom

This is the unterminated wiring loom for the ME360/ME221. Wires/connections are provided for on the ..

£125.00 Ex Tax:£125.00

Tags: Mazda, Throttle body, injection, ECU