DanST Engineering are pleased to be able to offer this complete bolt on kit for the Volkswagen 1.4 8v ABU, APQ, AEX and AEE engine codes. The package consists of the following:

 

1x TIG welded danST Engineering Aluminium inlet Manifold

1x Set of 37mm Keihin or Mikuni Carburettors

1x danST Engineering Carb Fitting Kit (4x Fluoro lined silicone hoses and 8x stainless mikalor clamps) in red, blue or black

 


We also offer a supplement pack as an add-on item. 

This is a package designed to be purchased with one of our bike carburettor starter packs and includes everything you will need to run your carburettors except for an ECU.

In the pack there is:

1x Linkage kit designed to adapt an existing cable,

1x Pipercross air filter and base plate,

1x New fuel pump

1x Sytec fuel filter.

This kit is ideal for anyone wanting to carry out the popular bike carb modification as an alternative to the old weber twin 40 style conversions. Bike carbs offer excellent performance, reliability and fuel economy when compared to the weber alternatives. These conversions are very popular in both modified and kit car circles and provide a low cost, simple power upgrade not to mention a fantastic soundtrack!

The manifold is manufactured from high quality aluminium with a precision Water Jet cut 10mm thick flange and TIG welded 45mm (Outside Dia) runners with a 3mm thick wall. All internal joints are fully ported/ground to ensure a smooth flow.

All danST supplied carburettors undergo a comprehensive inspection, strip, ultrasonic clean and rebuild process as required. Every set of carburettors are run on our dedicated test rig to ensure smooth idle and transition to higher RPM (see our youtube channel for running examples). We provide the carbs with base settings (and necessary jets) to allow you to get your engine up and running/driving. However these settings are only approximate and it is therefore essential that the carb jetting is set up by a competent engineer/mechanic using the necessary wide band AFR equipment (ideally on a rolling road) to avoid engine damage.

Please Note: All of our carburettor kits are made to order and therefore on a 10 working day lead time. This is to allow for manufacture of the manifold and preparation of the carburettors.

FAQ’s:

 

*******************************

What Else Will I need?

 

1.   Ignition.

 The carburettors in this kit will take care of the fueling of the engine, however you will need a means of running the ignition system and this will likely fall into one of the following categories:

1.1)     Distributor Based Engine. If your engine is equipped with a distributor as standard, this will work fine alongside the carbs to run the spark. Some distributor based systems have a vacuum line from the original inlet manifold. This vacuum reference gives additional advance at light throttle openings to aid light throttle response and economy, however many customers making performance upgrades including twin carbs simply opt to leave this line disconnected to simplify the install. If you do wish to retain this advance then our vacuum balance bar product must be fitted to our manifold to provide a stable signal (see our shop). One single tapping into our manifold is not sufficient and will result in a pulsed signal.

 

1.2)     OE Fuel Injection Engine. Depending on the standard management your engine is equipped with it may be possible to retain the standard ECU to run the ignition system. All original sensors and connections should be retained (with the exception of the original fuel injectors) to ensure the ECU has all the necessary inputs. If the ECU has a vacuum feed from the original manifold our balance bar product (see our shop) can be fitted to the new manifold to ensure the ECU retains this load reference.  One single tapping into our manifold is not sufficient and will result in a pulsed signal. If the vacuum line is not retained it is likely that the ECU will revert to a basic 2D ignition map similar to running a distributor.

 

1.3)      Standalone Ignition Controller. The ultimate ignition control is of course a standalone 3d mappable ignition controller such as the NODIZ Pro (see our shop for further details). This system replaces the distributor or OE management system entirely and enables full control of the ignition map, allowing maximum power and torque to be achieved at every point in the RPM range. This ECU takes inputs from a crank sensor (this will need to be retro fitted if the engine is not equipped with one as standard) and either a throttle position sensor or manifold pressure (MAP) sensor. See our shop for further details of the NODIZ Pro Ignition Controller.

2)  Fuel Supply

Motorcycle carburettors require a fuel supply pressure of 2-3psi. This can be achieved with one of the following:

 

2.1) Motorcycle Fuel Pump. Our bike fuel pumps are designed specifically to work with the carbs in our kits. They do not require a fuel pressure regulator and are an extremely simple inline install (in and out fuel connections and a 12v supply). Bike pumps should be mounted low down, close to the tank and horizontal. See our shop items for further details on our bike pump kits.

 

2.2) Aftermarket electric fuel pump and fuel pressure regulator. If you are upgrading from another aftermarket carb setup is is likely that this type of fuel system will already be in place. This can be re-used as long as a 2-3psi supply pressure can be achieved.

 

2.3) OE EFI Fuel pump and fuel pressure regulator. If the car is equipped with a fuel injection pump as standard the pressure will be considerably greater (typically 45psi+) than the required 2-3psi for the carbs. However there are regulators available that are capable of reducing this pressure sufficiently from EFI to carb requirements.

3) Throttle Linkage. The bike carb cable connection is relatively simple in comparison to other aftermarket carburettors with no complicated linkages required. In most cases it is simply a case of adapting the end of the existing throttle cable (inner and outer) to interface with the carbs. We can supply a universal cable kit that contains all of the parts to adapt an existing cable or make a cable assembly up (see our shop items).

4) Air Filters. It is important to protect your engine from airborn dust and debris and danST Engineering therefore always recommend running with an air filter fitted over our carburettor kits. We can supply a range of Pipercross PX500 and PX600 filters custom made to fit any carburettors used.

5) Rolling Road Tune. Our carburettors are all tested on our test bed and a base set-up carried out. This will ensure that with the carburettors installed your engine will start and drive. However final jetting and set-up must be carried out using the necessary AFR equipment and under real world load conditions (usually on a rolling road). This will ensure the maximum performance is achieved and will avoid engine damage that can be associated with running excessively lean or rich.

Bike carburettor tuning services.

 

danST Engineering are pleased to be able to offer bike carburettor diagnostic and set-up services using our in house chassis dynamometer (rolling road) based in Shipley, West Yorkshire. Please drop us a message to discuss your requirements.

Write a review

Note: HTML is not translated!
   Bad           Good

VW Polo 1.4 8v ABU, APQ, AEX & AEE Bike Carb Conversion Kit 37mm starter kit

  • £550.00

  • Ex Tax:£550.00

Available Options


Related Products

Bike Carb Fuel Pump

Bike Carb Fuel Pump

Bike carburettors are very sensitive to fuel pressure and require only a low pressure supply of 2-3p..

£58.33 Ex Tax:£58.33

Throttle Cable Kit for Bike Carbs & Throttle Bodies

Throttle Cable Kit for Bike Carbs & Throttle Bodies

A throttle cable kit designed to suit all bike carburetor installations, consisting of: 1.5m Long..

£20.83 Ex Tax:£20.83

Bike Carb Manifold Vacuum Balance Bar FITTED to manifold

Bike Carb Manifold Vacuum Balance Bar FITTED to manifold

In many engine applications a stable manifold absolute pressure (MAP) reading is required to control..

£50.00 Ex Tax:£50.00

FSE Sytec EFI Fuel Pump suitable for Bike Throttle Body Conversions

FSE Sytec EFI Fuel Pump suitable for Bike Throttle Body Conversions

FSE Sytec EFI fuel pump suitable for our danST individual throttle body conversions also a reliable ..

£75.00 Ex Tax:£75.00

Nodiz Pro Ignition ECU, Vauxhall Plug and Play Pack (Gen X)

Nodiz Pro Ignition ECU, Vauxhall Plug and Play Pack (Gen X)

PRELOOMED/PREMAPPED NODIZ Vauxhall SYSTEM If you have the factory Coil Pack and Crank Sensor..

£275.00 Ex Tax:£275.00

Throttle Cable LINKAGE Kit for Bike Carbs & Throttle Bodies

Throttle Cable LINKAGE Kit for Bike Carbs & Throttle Bodies

A throttle Linkage kit designed to suit our bike carburettor or throttle body installation..

£16.67 Ex Tax:£16.67

Bike Carburettor supplement package

Bike Carburettor supplement package

This is a packaged designed to be purchased with one of our bike carburettor starter packs and inclu..

£220.00 Ex Tax:£220.00

Ford Duratec HE 2.0, 2.3 and 2.5 Wasted Spark Coilpack Kit

Ford Duratec HE 2.0, 2.3 and 2.5 Wasted Spark Coilpack Kit

This is a package designed to be purchased with one of our bike or DCOE style throttle body conversi..

£141.67 Ex Tax:£141.67

2.5 Duratec Manley Long Rod and Racetec Piston Kit

2.5 Duratec Manley Long Rod and Racetec Piston Kit

 This long-rod piston kit has been developed to increase reliability and power from the Duratec..

£1,300.00 Ex Tax:£1,300.00

Throttle Cable ONLY for Bike Carbs & Throttle Bodies

Throttle Cable ONLY for Bike Carbs & Throttle Bodies

A throttle cable kit designed to suit all bike carburetor installations, consisting of: 2m Long I..

£10.00 Ex Tax:£10.00

Nodiz Pro Ignition ECU, Volkswagen ABF Plug and Play Pack (Gen X)

Nodiz Pro Ignition ECU, Volkswagen ABF Plug and Play Pack (Gen X)

PRELOOMED/PREMAPPED NODIZ Volkswagen ABF Engine If you have the factory Coil Pack and Crank Senso..

£275.00 Ex Tax:£275.00

Tags: VW, Polo, polo carburettors, carburetors