ME221 Standalone Fuel Injection ECU, Ford Duratec Plug and Play Pack

Description
Reviews (0)

ME221 Standalone Fuel Injection ECU, Ford Duratec Plug and Play Pack

This Ford Duratec specific ECU and loom kit has been specifically developed by Motorsport Electronics alongside danST Engineering to provide a plug and play standalone ECU solution for this popular engine. More specifically it has been tailored to suit the 2.5 Ford Duratec (US ford fusion among others) with its closed loop VVT system.

Description

The ME221 Wire-In ECU is a feature rich and future proof four cylinder injection engine management system. Built from the ground up using the latest control strategies means a modern, powerful, VE based ECU, with enhanced feature set including closed loop boost, in-built Wideband Lambda Control, DSP Knock Control, on-board data Logging and VVT control – all in a compact form factor. Massive IO means the ME221 can handle anything thrown at it, and custom tables means any specific algorithms required can be easily derived.

The ECU comes complete with a fully terminated Ford Duratec loom to get you up and running in no time. It is suitable for either the stock inlet, or throttle bodies.

Tuning Software (MEITE)

Intuitive, developed with real-world feedback from 100’s of tuners
Everything real-time adjustable
Diagnostics and analysis functionality
Custom layouts, tabs and functions
In-built firmware update tool for ease-of-use
Custom “part calibration” import – use settings from other maps in a current map
Offline Editing of calibrations
Real-time tracing
Data-logging of all variables and Auto-Tune

Fuelling Control

Configurable Load/RPM BINS 16×16, 32 bit floating point Tables
Multiple Fuel Tables
Injection Angle
Priming Pulse Settings and Crank Pulse Settings
Cranking Enrichment
After-Start Enrichment and ASE Time Decay
Warm-Up Enrichment
Acceleration Enrichement TPS/MAP based with Coolant Modifier
IAT Correction Table
Idle Trims
16×16 AFR Target Table factored into VE Equation
Speed-Density/Alpha-N with optional Blending
Injector Voltage Offset Table
Overrun Fuel Cut
Closed Loop Narrow-band/Wide-band Lambda control with Bosch LSU4.9 Controller On-Board
Flex-Fuel secondary tables

Ignition Control

16×16 32bit Table
Closed Loop DSP Windowed Knock Control On-board
Battery Voltage Dwell Correction 16×16 Table
Individual Cylinder Trimming
IAT and Coolant Trim
Spark-Scatter Ignition Idle Control
Flex-Fuel Control
Switchable Ignition Tables

Crank/Cam Triggering

VR/Hall/Opto Inputs as required
Auto-scaling, Parametric Noise Rejection
Range of OEM Patterns Supported

Idle Control

PWM based Closed/Open/Manual Diagnostic Modes
4-wire Stepper based idle control
Cranking/Return to idle Settings reference Open-Loop table for wide-control
DBW Idle Control *where DBW is used
AC/Fan Auto-Idle Up Settings
PID Based for Accuracy
Fuel Modifiers
Ignition Spark Scatter
Jacked-Throttle Miss-Bang Idle Mode (Group-N ALS)

Knock Control

DSP Angular Windowed Knock Control
Settable Gains, Offset and Window Duration
Step Retard and Fail-Safe

Boost Control

Closed/Open Loop Boost Control by 16×16 RPM and Throttle table
Boost-by-Gear
Switchable Boost Tables
Over-Boost Protection
Pre-Start Duties
Anti-Lag Group-N

Variable Valve Timing

Fully Closed Loop PWM (Throttle X RPM table)
Dual Cam Support
Locked Angle or Locked Duty testing modes
Basic On/Off Mode (Honda V-Tec)
Supported patterns include MX5 2001-2005 and Ford ST170, Ford Puma 1.7
PID Tuning with Oil Temperature triggering & safeties
Programmable Rest State & Offset compensation

General Purpose Tables

6x General Purpose Tables
Custom Variables and Outputs
Modify Fuel, Ignition, Boost and Idle strategies from the GPTs
3D and 2D tables with ability to “chain” tables together for create complex functions

Communications

Industry Preferred RS232 for ECU mapping/communication (USB Adaptor available)
CAN-Bus on some models
USB on some models

Processing Power

120Mhz 32-bit RISC Processor
Ignition Accuracy to 0.01 degrees, Fuelling to 0.001mS
32-bit maths and tables (Table entries can have 8 decimal places for very high resolution)
ADCs/Analogue data reported to 16-bit accuracy
20,000+ RPM

Analogue/Digital Inputs

Configurable “HRT”‘s for every analogue channel – use any sensor. Basemaps pre-set for factory sensors.
Wide-band O2 LSU4.9 Controller Built In
TPS, IAT, CLT, MAP, Lambda standard inputs
Selectable feature for digital/analogue inputs
Spare/unused analogue lines can be used for general purpose tables or digital switches

Environmental & Physical

Automotive -20 – 85*C
Voltage 5.5-28V
Operating Current Approx 120mA @ 13v
Electrically isolated and protected inputs/outputs
90 Way Automotive Connector
IP67 Sealed Alloy Casing

DataLogging

4Gb On-board Data logging – over 2,000 Hours of all variables
Unlimited PC based logging via MEITE
User settable Triggers and markers

**Please Note, This is designed to suit the Ford derived 2.0 Duratec as would be fitted in the fiesta ST150**

This package includes the ME221 ECU, Duratec Plug-n-Play Loom, RS232 Tuning Cable & Quick Start Sheet.

The ME221 Duratec loom is complete with the stock Duratec Cam & Crank sensor, Throttle Sensor, Coil-pack and VVT solenoid connections. MAP, Intake Air and Coolant connections are a Bosch 2-pin mini-timer type.

This system will give precise, closed loop control of the VVT system on both the 2.0 Mazda and 2.5 Ford variants of this engined – gains of over 30 ft/lbs have been shown when using closed loop VVT as opposed to locking the cam.

Note that as with all after-market engine management systems, basemaps are offered ‘as-is’, and dyno tuning is recommended to avoid damaging your engine. We have full rolling road facilities on site.

Our Youtube Channel is an invaluable source of information for anyone looking to install this or any other danST product. The below instructional video details the installation of an ME221 Duratec into a 2.5L Duratec powered mk6 fiesta:

Fiesta MK6 ME221 Duratec Loom Installation Guide

The connections provided in our FORD Duratec loom are:

4x EV14 for the Injectors

1x 2 pin Ford Duratec VR Cam Sensor

1x 2 Pin Ford Duratec VR Type Crank Sensor

1x 2 Pin Ford Duratec for VVT Solenoid

1x 2 Pin Mini-Timer for IAT and Coolant sensor ○ Note may need extending/changing depending on the engine type. Use OEM connectors.

1x Ford (Zetec/Focus) oval Coil Pack Connector

1x 3 Pin Mini-Timer for throttle sensor ○ Typical if using throttle bodies - may need to change if keeping OEM throttle sensor though this is rare.

1x 3 Pin Mini-Timer MAP sensor (suits our 3 Bar Sensor)

1 x Bosch O2/Lambda Plug.

Auxiliary flying wires for spare outputs, tachometer, and knock. The loom also features Built-in Ignition and Fuel Pump relay block with fuses.

What is in the box:

1 x Standalone ME221 Engine Control Unit (ECU)

1 x Duratec Loom

Options

Coolant and air temperature sensors. The ME221 and MEITE software do offer the ability to calibrate the ECU to read any sensor, however by using the sensors on offer in this listing the standard calibration tables can be used - vastly simplifying the set-up process and saving considerable time. Both sensors are M12 x 1.5 thread. The additional coolant temperature sensor housing offers a quick and convenient method for installing directly into a radiator top hose and negates the need for tapping out existing holes in your cylinder head.

Data Cable (FTDI USB-Serial Adaptor). Whilst the ECU comes with an RS232 cable many modern Laptops do not have such a connection. Therefore this adaptor will allow a USB port to be used for connectivity. This genuine FTDI cable is guaranteed to work with this ECU, unlike many cheaper alternatives that often suffer connectivity issues.

Basemaps

ALL ME221 and ME442 ECU's are shipped with a test map only. This is highly unlikely to run your engine and if it does it will not run it very well! A library of basemaps can be found here on the Motorsport Electronics Support Pages as well as a full suite of installation manuals. danST Engineering can also provide basemaps for a variety of engines developed on our in-house rolling road.

Coil Pack Compatibility

This ECU is intended for use with wasted spark Ford coil packs. The loom has the Zetec oval style coilpack connector - therefore this type of coil should be used, else the plug on the loom will need to be changed if you wish to run the small square plug coilpack (Duratec, Fiesta ST150). Other wasted spark coil packs may be compatible however please contact us before attempting to use alternatives to avoid potential damage to the ECU. The fitment of a Ford coil pack (available in our shop) will guarantee compatibility and reliability.

Note: As with all after-market engine management systems (ECU’s) a dyno tuning is recommended to avoid damaging your engine and to get the most out of your engine. A full range of basemaps are available online from danST engineering or Motorsport Electronics

Description

Our Youtube Channel is an invaluable source of information for anyone looking to install this or any other danST product. The below instructional video details the installation of an ME221 Duratec into a 2.5L Duratec powered mk6 fiesta:

Fiesta MK6 ME221 Duratec Loom Installation Guide